|
|
Cầu đo điện trở tiếp xúc Model MMR-630 |
Index:WMGBMMR630 The MMR-630 Series meters are professional portable instruments for measuring very low resistances. Due to their special measurement algorithm they can be used for both resistive and inductive type of a specimen that makes MMR-630 series perfect instruments for electricians testing electrical ju ... |
|
Index:WMGBMMR630 The MMR-630 Series meters are professional portable instruments for measuring very low resistances. Due to their special measurement algorithm they can be used for both resistive and inductive type of a specimen that makes MMR-630 series perfect instruments for electricians testing electrical junctions, motors and power transformers windings. The results can be stored in the internal memory and send to a computer via serial interface. A quick PASS/FAIL test function with results displayed and acoustically indicated simplifies measurements considerably.
MMR-630 Technical Specifications Measurement of resistive object type: - - welded and soldered connections, equipotential bonding, earth wire,
- terminals and connectors, rail welded joints, cables and wires, - measurement 4-pole method.
- Measurement of inductive object type:
- coils (motors and transformers), low resistance coils. - Range selection autoranging or manual (measurement of inductive object type).
- Selectable measurement mode adjusted to object type:
- for resistive objects - fast mode (3 seconds), - for inductive objects - long mode with automatic discharge after measurements (or with lower accuracy - shorter mode). - Selectable measurement mode adjusted to application:
- normal mode - after pushing „START” button, - automatic mode - since test leads are connected to the object meters automatically starts measurement with dual direction current flow and gives average result - what eliminates eventual DC voltage on tested object, - continuous mode - every 3 seconds for resistive objects or continuous measurement for inductive objects. - Window mode:
- this option enables setting an upper and a lower limit between which the average measurement result is bound to appear. The results outside of this range will be indicated by two long audible signals and the symbols. - MMR-630 is designated not to be effected by interference up to 20mV and to show noises from 20 to 100mV (so in edge conditions even 5 times higher than measured drop of potential).
- Memory store for up to 990 results and a communications facility for transferring data from the device to a PC.
Electric security: - type of insulation: double, according to EN 61010-1 and IEC 61557 - measurement category: CAT III 300V acc. to EN 61010-1 - protection class acc. to EN 60529: IP54 Other technical data: - meter’s power supply: battery package SONEL/Ni-MH 4,8V - battery charging time: approx. 2,5 hours - number of measurements with the current of 10A: 300 - auto-off time: 120 seconds - immunity to interference: additional error ≤1% for voltage 50 Hz ≤100mV RMS - maximum leads resistance for the 10A current: 0,1Ω - maximum inductance of the tested object: 40H - accuracy of the test current: ±10% - resistance measurement time: - with the selected resistive object type with the bidirectional current: 3 seconds - with the selected inductive object type, dependant on the resistance and inductance of the object: a few minutes (max. 10) - dimensions: 295 x 222 x 95 mm - weight: approx. 1,7 kg
Rated operational conditions: - operation temperature: 0...+40°C - storage temperature: -20...+60°C
MMR-620 microohmmeter conforms the following directives or standards according to CE requirements.
Directive: Low Voltage Directive (LVD) 73/23/EEC, 93/68/EEC.
Standards: EN 61010-1:2001 Safety requirements for electrical equipment for measurement, control and laboratory use. General requirements . EN 61010-031:2002: Safety requirements for electrical equipment for measurement, control and laboratory use. Safety requirements for hand-held probe assemblies for electrical measurement and test.
Directive: Electromagnetic compatibility (EMC) 89/336/EEC, 92/31/EEC, 93/68/EEC.
Standards: EN 61326:1997+A1:1998+A2:2001 Electrical equipment for measurement, control and laboratory use - EMC requirements.Resistance measurement MMR-630 | Current | Accuracy | Range | Resolution | 0...999,9μΩ | 0,1μΩ | 10A
| ±(0,25% m.v. + 2 digits)
| 1,0000...1,9999mΩ | 0,0001mΩ | 2,000...19,999mΩ | 0,001mΩ | 20,00...199,99mΩ
| 0,01mΩ
| 1A
| 200,0...999,9mΩ
| 0,1mΩ
| 0,1A | 1,0000...1,9999Ω
| 0,0001Ω | 2,000...19,999Ω | 0,001Ω
| 10mA
| 20,00...199,99Ω | 0,01Ω
| 0,1mA
| 200,0...1999,9Ω | 0,1Ω | 0,1mA |
- input impedance of the voltmeter: ≥200kΩ„m.v.” - measured value.
|
|
|
|